Major help needed (long)

Warning lots of gory algae details


I am having a huge problem with algae that is getting worse. Even new growth is covered by algae in a few days. This is mostly hair algae (very long strands) and beard algae, I noticed some brush algae on a small sword as well. I constantly pick and prune - I am injecting C02 from a tank and a DIY reactor similar to the one describe on this site. The tank has been setup for over six months and has never been completely without algae. I had BGA one month after I setup the tank that I cleared with a blackout and maracyn. Until about four weeks ago the tank was going along fairly well - too much algae but I could control it with pruning. I then did a water change and left for a trip, sometime right after I left the filter stopped working. When I got back I had a full blown case of green water and the glass was covered with algae. I bought a new filter, put a UV sterilizer in line, cleaned pruned, did several massive water changes, and it has been a slow down hill slide since then. I am picking half a bucket of algae a week out of the tank. Plant growth is very good and I am constantly having to prune and replant. One anacharias stem grew over three feet last week. The plants (and algae) start perling like crazy as soon after the lights come on.


Tank 150 Gallon
Filter XP3 and a very small hob that I use to disolve ferts into the tank turning it off makes no measurable difference in C02 levels
Flourite (3 inches)
Plants (Luwidga, Mayca, Anacharias, Annubia, Forest of Vals, some Hornwort)
Fish ( Roughly 20 small tetras, 2 cory cats, 2 yoyo's, 6-8 oto's, many snails)
Light Compact Flourescent 400W (10 hours a day)
C02 Injection (cylinder) Reactor with a Rio 600 (2 inch diameter 12 long)

(Well Water)
Ph - 8.5 (7.2 out of tap - 8.5 after 48 hrs)
KH - 17-18 (Well water from KH kit)
GH - 10
Nitrates - A trace of of the tap
Phosphates - 3 ppm out of the tap

Tank
Ph - 7.2-7.6 (7.2 before lights on - climbs to 7.6 before lights out)
Nitrates - 30 ppm (test by myself and two LFS's)
Phos - 3 pmm
Nitrite - 0
NH4 - 0
Micros - Greg Watson - 50 ml every other day

Tank Schedule
Day 1 - 75% water change - prune/pick algae - 3 tsp KN03, 1tsp K2SO4
Day 2 - 50 ml micros (CSM+B) - pick algae- I check KNO3 and add if necessary
Day 3 - 3 tsp KNO3, 1tsp K2SO4, 1/4 tsp KH2PO4 - pick algae prune
Day 4 - same as day 2
Day 5 - Same as day 3
Day 6 - Same as day 2
Day 7 - Same as day 3

- Does anyone see anything wrong ?
- I recently up the micro's and the algae loves it
- Do I start over ?

What do I do next ? I'm ready to give up, bleach everything, and hang a night light over the tank, maybe grow blind cave fish in a blacked out tank

Scott

Re: Major help needed (long)

Ok, I'll bite and I'm not trying to be difficult I'm trying to learn - Why do I need to increase C02 ? Also it appears that adding Micros increases algae growth ? Moving the ph with my KH at 17 isn't easy. Anyone else have a KH of 17 ? I have great plant growth - I have to prune the anacharias and hornwort every other day. The vals are growing several inches a week and sending out new shoots like crazy. Everything is perling like crazy - the walls of the tank will be coated with bubbles when I get home this evening. Is a few hours of keeping the CO2 up really going to make a difference? I have kind of watched the PH over the past couple of weekends and it goes up like this

10:00 am lights on - Ph 7.2 - C02 30 ppm
12:00 noon - Ph 7.3 - C02 26 ppm
4 pm - Ph 7.4 - C02 20 ppm
6 pm - Ph 7.5 - C02 16ppm
7 pm (50% lights off) - ph 7.5 - 7.6 CO2 -16 ppm - 13 ppm
8 pm (all lights off) - Ph 7.3 - 7.4 CO2 - 20ppm
10 pm - Ph 7.2 - Controller kicks C02 off

Scott

Re: Major help needed (long)



I'm using your design , I will admit it's the best of the three I've tried so far. I'll add a second one and maybe it's time to order an 80lb tank

Scott

Re: Major help needed (long)

Tom, bear with me but something is still way out of kilter kere . KH is a horrible term, let's say something in the water that causes a test kit to return a KH (alkalinity) of 17.5 and something causes a PH reading of 7.2. Last night adding a second reactor should have made some change. Sheesh I'm dissoloving a steady stream of bubbles in one reactor and I add a second one bumping up the C02 and it doesn't change the PH at all ? Even running the reactors overnight ? I also added tight fitting glass covers and turned off the hob (had too to fit the cover on that side) it should have had some effect to drive the PH down at least a little bit it's 7.6 right now. I also really cranked the C02 up this morning, I just checked and I'm I have very steady stream of bubbles at the reactors (too fast to count) and it looks like most of the C02 is desolving. Assuming that both reactors are equally effective I should have come close to doubling the dissolved C02. I don't see fish gasping at the surface, but given the perling is it possible the my C02 content is higher than the C02-PH-KH table is reporting ? Could there be a red herring that is tripping up one of the tests ?

I'm not throwing anything else at this until I have a better understanding of what's going on. I'm going to setup up my quarantine tank (20 gallon) tonight and do some experimenting. I'm going to set the tank up bare, pull water from the 150 and stick one or perhaps both of the reactors into the 20 and see what happens. Do you agree that with a 20 gallon tank that I should be able to drive the PH very low or do I need to connect a small V8 to the reactor ? I can also replace the pump on one of the reactors with my water change pump 400 gph although I may need to increase the length of the reactor again to keep from blowing the C02 out the bottom. This is getting a bit frustrating.

Scott

Re: Major help needed (long)

The strangeness continues. got home last night and the PH was 7.6 and just before lights out it was 7.5. One hour after lights out it was down to 7.2. I was going to move my quarantine tank over to the main tank and fill it when I found a couple of missing 5 gallon buckets in the stand of the 20.

I filled a bucket with tank water - PH 7.3 - I put the reactor and PH probe into the bucket and in about 20 minutes pulled the bucket down to PH 7.1 and after an hour I got it to 6.9. I was thinking at this point that I was going to have to improve my reactor(s) in the main tank. When I went to return the reactor to the tank I noticed a couple of fish gasping at the surface and when I returned the PH probe to the water the PH was 6.9. Never in the past month have I been able to get the tank this low and I did it with the one original reactor. I double checked everything and even recalibrated the PH probe again. The PH controller and an a brand new AP PH (9/04 mfg date) kit agree with each other. The probe responds almost instantly to the 4.0 and 7.0 solutions.

This bugged me all night so early this morning (5am to be exact) I filled another bucket with tap water (ph 7.2) and I put the reactor in and went back to bed (5:25 am). I checked the water in the bucket at 8:30 just before I left for work and it was at ph 7.2. It really does appear that I have something in my water buffering my PH.

I'm not going to have time to play with this again until the weekend but I want to repeat this experiment again. FYI I double checked the alkalinity in the tank this morning and it is actually a little higher than the tap maybe 17.5 - 18. The water from the tap changes color right at 17, when I do the water from the tank it starts to shift at 17 but doesn't fully change until the 18th drop is added. Could this be caused by the extra Phosphate added to the tank ?

Scott

Re: Major help needed (long)

Laith there has to be something else going on - read a little closer. It's not just dissolving the C02, although I agree that part of the solution maybe to get more aggressive with the injection of C02 after a water change. Let me summarize.

150g tank
1. One reactor - run overnight - PH 7.2 - (last three weeks)
2. Two reactors - run overnight - PH 7.2 - (added 2nd reactor Monday eve)
3. ?????? Original reactor running for 2 hours last night pulls tank to 6.9 ???? Other reactor was in 5 gallon bucket

5 gallon buckets (say 4.5 gallons total water)
1. Tank water 1 reactor one hour PH 6.9
2. Tap Water 1 reactor (same reactor above) three hours PH 7.2

If it's just disolving the C02 why suddenly last night am I able to pull the tank down to 6.9 with one reactor ? Also again if it's just dissolving C02 why did the 5 gallon bucket get stuck at ph 7.2 this morning ? I need to repeat the 5 gallon bucket experiment but it's going to be tomorrow night or Sat before I can get to it. I need to get a little more scientific and modify one parameter at a time.

Scott

Re: Major help needed (long)

I love the web - I did some googling and found the tests for some wells in the area of the county that I live in. Anyone see anything odd in here ? We have a water softener so our tapwater hardness (GH) is very low. While the alkalinity is very high. Anything look odd to anyone ?

Well No. 3 7
Well Depth (feet) 387 350
Capacity (gpm) 200 450
Depth to Bedrock(ft) 50 238
Water-Bearing Formation4 LS LS

Chemical Constituents
Total Dissolved Solids 743 660
Hardness (as CaCO3) 571 480
Iron 0.5 not/tested
Chloride 14.3 9.5
Sulfate 245 257
Fluoride na 69

Re: Major help needed (long)

I did a lot of testing this weekend and something in my well water is causing some kind of bufferring effect. I pulled two five gallon buckets of water out of my tank and I took two five gallon buckets from the tap. I used a couple of powerheads to stir up the water and free any C02 in the water. If I put the reactor into the tank water (1 week old, PH 8.2 after 12 hours of agitation) and let it run the PH drops rapidily and within the hour it is PH 6.8. If I do the same with tap water the PH drops rapidly to ph 7.6, slowly goes to 7.2, sits at 7.2 then goes down to 6.8. this took around 90 minutes on both buckets of tap water.

Now that I understand that I have this effect, I'm modifying my water change protocol to help deal with it. I have always done 50-75% weekly water changes usually closer to 75%. I'm going to switch and start doing 25-30% water changes twice a week. I'll probably vacuum on one change and just pull out water on the other. This should decrease the time that it takes me to get through the bufferring effect and I should be able to maintain a more stable PH and C02 level. I did the first of these changes around 1:00 yesterday, I did a 25% water change and turned on both reactors. This worked much better, by 6:30 pm I had the PH stable at 7.1.

Scott